Cables

Protection where it's needed; Tube Tops can be placed virtually anywhere cable housing comes into contact with a bicycle frame. Designed to protect a frames finish Tube Tops can also be used to quiet cable slap.

Jagwire's Straddle Cable Carrier is for cantilever and centerpull brakes. It attaches to the end of the brake cable and is what the brake's straddle (also called transverse or crossover) cable attaches to. The Straddle Cable Carrier is made of light, corrosion-resistant and durable aluminum with a steel bolt. You get a pack of 10.

Jagwire's Cable Grips are adapters that make it possible to run hydraulic brake lines on bicycle frames that have housing stops that were designed for regular wire cables and standard housing sections. Once the regular cables and housing sections are removed, the Cable Grips are inserted and tightened in place in the standard frame stops. Then, the hydraulic lines are attached and securely held in place by the gripping jaw(s) of the Cable Grips. - Aluminum model accepts lines up to 5mm in diameter and the lines snap in. - Stainless model grips fully around the lines and is adjustable to fit most diameters.

Jagwire's M7 Adjusting Barrel is a 7 x 1.0mm-threaded replacement cable-adjusting barrel. It's the right part for many older-style mountain bike brake levers. It comes in two models and is made of durable metal with a lockring for locking your adjustments. You get a pack of 10.

DIY Kit Includes: - Housing and Shift Cable - End caps and cable tips - Compatible Shimano/SRAM Specs: - Cable Material: Galvanized - Intended Use: Road/MTB - Cables & Housing Comp: Shimano/SRAM - Housing Length: 2000mm

The Odyssey K-Shield Linear cable features a pre-stretched inner Slic Kable covered in a linear casing to prevent binding and an outer K-Shield mesh housing for less weight over a standard steel mesh housing (2.9 oz). - Black - 60 – 65mm

- Vision Aero/reverse brake lever specific brake cable - Replacement cables that only work with Vision reverse brake levers - Sold individually

- Stainless steel slick extruded surface - 1.1mm x 2100mm - Pre-stretched for precise shifting - Permanent rust free performance - Shimano & SRAM compatible

- Replacement cable for the Jagwire Pro Dropper kit - 0.8mm inner cable is more flexible and has lower friction than typical shift inner cables - An easy way to reduce the force required to activate a dropper post remote lever - Perfect for dropper seatposts with "stealth" cable routing and tight housing bends - Includes 2x heat-shrink shims - For use with dropper seatposts ONLY - Length: 2000mm

Slick stainless cables undergo a polishing process to further remove imperfections. This creates a smoother surface with lower friction than PTFE-coated cables. With no coating, these are highly durable and compatible with all performance housings and lubricants. Typically used on high-end bikes, by riders wanting improved performance. Pro Polished cables eliminate the need for flaky coatings with an innovative polishing process to reduce friction and improve performance. - Polished stainless steel construction for low friction - Compatible with all performance housing and lubricants - Cables are tinted gold for easy identification

Aluminum, Lightweight, Lubricated An alternative to traditional compressionless housing, this system is made of nesting alloy pieces that protect the liner. Although this housing is typically more expensive, it has several advantages including increased flexibility, reduced weight and increased durability. Both shift and brake housings use identical Slick-Lube liners and interconnecting alloy pieces. - Slick-Lube liners reduce friction and protect against corrosion - Includes four 1600mm liners

Aluminum, Lightweight, Lubricated An alternative to traditional compressionless housing, this system is made of nesting alloy pieces that protect the liner. Although this housing is typically more expensive, it has several advantages including increased flexibility, reduced weight and increased durability. Both shift and brake housings use identical Slick-Lube liners and interconnecting alloy pieces. - Slick-Lube liners reduce friction and protect against corrosion - Includes four 2300mm liners

Sport level brake cables come in a variety of cable end setups to fit most bikes at a quality level well above normal OEM cables. - Slick cables are die-extruded for smooth operation - Pre-stretched - Double-ended SRAM/Shimano mountain and road compatible cable ends - Stainless steel construction resists corrosion - Double Ended: Yes - Cable Head: Shimano/SRAM Road, Shimano/SRAM Mountain - Defined Color: Silver - Quantity Included: 1

Slick stainless cables undergo a polishing process to further remove imperfections. This creates a smoother surface with lower friction than PTFE-coated cables. With no coating, these are highly durable and compatible with all performance housings and lubricants. Typically used on high-end bikes, by riders wanting improved performance. Pro Polished cables eliminate the need for flaky coatings with an innovative polishing process to reduce friction and improve performance. - Polished stainless steel construction for low friction - Compatible with all performance housing and lubricants - Cables are tinted gold for easy identification

Jagwire's Stick-On Cable Guides are made of lightweight aluminum with adhesive on the bottom. The aluminum lets them conform to any shaped frame tube and the adhesive holds fast. They come with Jagwire's C-Clips, nylon cable clips that snap onto the guides to hold the cables neatly in place. You get a pack of 4.

Jagwire's Alloy Straddle Cable Carrier w/Liner is a nice upgrade for your cantilever brakes. It's made of light and durable aluminum and has a liner for smooth action.

Jagwire's M6 Adjusting Bolt is a metal adjusting barrel that is the correct replacement adjusting barrel for the cable clips/hangers found on many cable brake systems old and new. It makes it easy to tighten/loosen your brakes without tools. Its 6 x 1.0mm threading fits most clips/hangers and it has a lockring for locking your brake adjustment once it's set. You get a pack of 25.

Jagwire's Sport Inline Adjusters are installed on your shift cable housing sections so that you can fine-tune the shift cable tension by hand (without tools). They're great for keeping your shifting dialed in. They're precision made of lightweight aluminum and nylon for easy use and durability. To install them, remove the cables and housing sections, cut the top housing sections in two and rejoin the sections with the Inline Adjusters in the middle.

Replacement parts for Jagwire's Elite Link kits keep things functioning as intended. - Extra links for long housing runs or replacing damaged sections - 20 links at 10mm of length each

Hose fittings for Hayes hydraulic disc brakes available a la carte. Hayes brake compatibility: - HFX-9 - Prime - Sole - El Camino - Radar

- Nano-polished ultra slick extruded cable is non-coated for ultimate smoothness and durability - Double ended for Shimano/SRAM road and MTB brake levers - Pre-stretched for more responsive braking - 1.5mm x 1700mm

A great replacement for OE cables and a perfect way to bring style to a bike, the 1x Sport Shift kits make it easy. They come with a weld-cut single-ended Slick Stainless cable for easy installation with modern SRAM and Shimano shifters. The included housing uses our Slick-Lube liners to reduce friction, providing shifting precision and long-lasting performance. This kit is designed for use on bikes with a 1x drivetrain with a rear derailleur or internally geared hub. - Single-ended shift cable is compatible with SRAM and Shimano shift levers for both road or mountain bikes - Sport Slick Stainless cable combines with a Slick-Lube housing liner to offer dependable shifting performance and durability - Includes everything needed for a complete shift cable and housing replacement for a rear derailleur or internally geared hub - OEM-level cables and housing with high-quality small parts

Inline adjusters make on-the-fly derailleur cable tension adjustments safe and easy. - 5mm - Stronger detent mechanism for use with brake housing - Perfect for mechanical disc brakes

Inline adjusters make on-the-fly derailleur cable tension adjustments safe and easy. - Indexed adjustment for braided shift housing - Not recommended for use with brake systems

- Nano-polished ultra slick extruded cable is non-coated for ultimate smoothness and durability - Compatible with Shimano/SRAM road and MTB shifters - Pre-stretched for more responsive braking - 1.1mm x 2300mm

Rocket II direct cable adjusters fit into Shimano STI shifters with external shift cable routing. - Rubber coated adjusting knobs for firm grip - Adjustable on the fly - 4mm

SRAM's Inline Barrel Adjusters are placed on your brake cables near the handlebars so that you can turn the adjusters to fine-tune your braking. They feature durable and light aluminum/composite construction with rubber covers for easy operation.

Jagwire Elite Link End Cap Packs include each of the specialty housing end caps found in the corresponding Jagwire Elite Link DIY kit. - Includes specialty end caps for the 2x Elite Link Shift Kit

Jagwire's M10 Adjusting Barrel is a 10 x 1.0mm-threaded replacement cable-adjusting barrel. It's the right replacement part for most mountain bike brake levers. It's made of durable metal with a lockring for locking your adjustments. You get a pack of 10.

Mountain Pro Quick-Fit kits allow the easy installation of Jagwire hose with Shimano disc brakes. Kits contain enough hardware for both front and rear brakes. - Requires Jagwire Mountain Pro Universal Disc Brake Hose Kit for installation - Compatible with: Shimano Deore M596, M615